| M11-1034-010 RETAINING RING, EXT |
| 691-15-0 PINION RETAINER |
| M27-1001-010 ANTI-VIBRATION RUBBER MOUNT |
| DT23974-2 CHAIN LINK, RETENTION, GUARD, POS, BUW |
| GREASE NIPPLE, 1/8 NPT X 1 1/4 LONG FOR TOP DRIVE PT.NO:R01-1003-01A |
| H10059 VLV, HYD, DIR, 3 POS, 4 WAY, 24V, D03 |
| AY12300 COOLER ASSY, RECOVERY AIR, AC |
| SH-0750NC-0200-W CAPSCR, HEX SOC HD, 3/4-10UNC x 2.00, W |
| H10165 VLV, HYD, NEEDLE, SAND, D03 |
| CARTRIDGE, P.O. CHECK FOR TOP DRIVE PT.N O:H10071 |
| 681-11-1-005 SHIM, 0.005″ |
| M10035 DOWEL PIN |
| SH-0625NC-0200-W CAPSCR, HEX SOC HD, 5/8-11UNC x 2.00, W |
| M17-1007-010 ROLL PIN, 1/2 x 1.25 |
| FUSE HOLDER P/N:E10360 For Top Drive |
| AY11619 KIT, J-BOX, ANTI-VIBRATION MOUNT |
| S01-1267-01N O-RING |
| M14-1000-010 SPRING |
| H15-520601-08 UNION, BULKHEAD, MALE 1/2 ORFS |
| HH-0250NC-0063-GR8-W CAPSCR, HEX HD, 1/4-20UNC x 0.63, GR8, W |
| LW-12MM-IT LOCKWASHER, 12MM INT TOOTH |
| HN-0750NC-GR8 HEX NUT, 3/4-10UNC, GR8 |
| BH-6-32-0050-SS CAPSCR, BUTTON HD SOC, 6-32 UNC x 0.50 |
| MOTOR, HYD, 12.9 CI FOR TOP DRIVE PT.NO: H02-1003-030 |
| S01-1266-01N O-RING |
| AY16278 GREASE TUBE ASSY, NON-DRIVE END, GE |
| SH-0750NC-0125-W CAPSCR, HEX SOC HD, 3/4-10UNC x 1.25, W |
| 681-11-1-003 SHIM, 0.003″ |
| 683-14-0 PISTON, CBAL CYL, 2.50 DIA |
| HH-0250NC-0088-GR8-W CAPSCR, HEX HD, 1/4-20UNC x 0.88, GR8 |
| TERMINAL GROUND TS 35 RAIL 5.2MM P/N:E10932 For Top Drive |
| BLOCK ADAPTER RTD HYD VALVE BANK P/N:DT13833 For Top Drive |
| DT22650 LIMIT SWITCH GUARD, MODIFICATION |
| ROD, SPRING GUIDE, STABBING BELL FOR TOP DRIVE PT.NO:829-17-0 |
| SH-0500NC-0100-W CAPSCR, HEX SOC HD, 1/2-13UNC x 1.00, W |
| M11-1049-010 RETNG RING, EXT |
| VALVE, CHECK, SIDE TO NOSE, CXCD-XAN FOR TOP DRIVE PT.NO:H10287 |
| SH-0312NC-0500-W CAPSCR, HEX SOC HD, 5/16-18UNC x 5.00, W |
| DIE BLOCK, 5.75 – 9.00 IN DIA FOR TOP DR IVE PT.NO:DT14330 |
| RTD 100 OHM PLATINUM 3 WIRE 2 1/2in P/N::DT11348 For Top Drive |
| S01-1340-01V O-RING |
| HH-0375NC-0325-GR8-W CAPSCR, HEX HD, 3/8-16UNC x 3.25, GR8, W |
| 681-11-1-030 SHIM, 0.030″ |
| M17-1006-010 ROLL PIN, 1/2 x 1.00 |
| MOUNT FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: 587-52-2 |
| LN-6-32NC-SS LOCKNUT, #6-32UNC, SS |
| H25-1004-010 CLAMP, SINGLE, 3/4 IN DIA |
| H15-090109B-06 PLUG, SOC HEX, 3/8 ORB |
| BUSS BAR, C-SHAPE, 3/8 THK x 2.00 P/N::DT11348 For Top Drive |
| LUBE OIL COOLER, RECOVERY AIR FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: AY11598 |
| DT25332 RETAINER, TOP PLATE, BUW, INNER |
| FW-M12-A WASHER, F, M12, DIN 125A, ZINC PLATED |
| SWITCH PRESSURE 700-3100 PSI P/N:N10058 For Top Drive |
| PAD, PRESSURE, 650 TON FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: 912-16-0 |
| VALVE,CHECK, NOSE TO SIDE, CXJA-XAN FOR TOP DRIVE PT.NO:H10288 |
| 315-12-0 PINION, 28T, INT TAPERED, SPUR, TB |
| SHIELD, OIL FOR TOP DRIVE PT.NO:685-24-0 |
| LOCKWASHER, 12MM INT TOOTH FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: LW-12MM-IT |
| DIAPHRAGM FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: M16-1002-01A |
| DT24411 PLATE, PERFORATED, GUARD,1250AC/1275AC |
| COMMON LINK 63MM F-FRAME P/N:E11004 For Top Drive |
| ENCODER SHAFT P/N:DT11728 For Top Drive |
| ORIFICE, 1.0MM, PUSH-IN FOR TOP DRIVE PT .NO:H13-1017-010 |
| COUNTERBALANCE VALVE UPDATED TO VLV, HYD , CBAL, 4.5:1 RATIO, SAE-8, D05 FOR TOP DRIVE PT.NO:H09-1004-010 |
| END PLATE, UK 3 N OR UK 10 N P/N:E10926 P/N::E10926 For Top Drive |
| GASKET, MOTOR/GEAR BOX FOR TOP DRIVE PT. NO:602-40-0 |
| LOCKING KIT, PB SWITCH, FLUSH HEAD FOR T OP DRIVE PT.NO:E06-6000-01F |
| 602-26-0 SPRING |
| GAUGE, PRESSURE, 0 – 3000 PSI, SS FOR TO P DRIVE PT.NO:N01-1003-010 |
| RETNG RING, 7500 PSI, 4 IN FOR TOP DRIVE PT.NO:R01-3009-010 |
| BREATHER, 3/4 NPT FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: H13-1002-010 |
| TERMINAL GND DBL COMBI-FT 24-12 AWG P/N::E10536 For Top Drive |
| M11-1007-010 RETAINING RING, EXT |
| GASKET, VIEWCOVER, GRCASE, 12.25 X 5.25 FOR TOP DRIVE PT.NO:911-14-0 |
| DT11482 BUSHING |
| SH-0250NC-0038-W CAPSCR, HEX SOC HD, 1/4-20UNC x 0.38, W |
| LW-0500-ET LOCKWASHER, 1/2 EXTERNAL TOOTH |
| GASKET, COVER PLATE, TORQUE BOOST FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: DT12152 |
| M14-1011-010 SPRING, COMPRESSION, .81 ID X 1.37 OD |
| N10843 ENCODER, 2048, HAZ AREA |
| H10052 PRESSURE REDUCING VALVE |
| PISTON, CBAL CYL, 2.50 DIA FOR TOP DRIVE PT.NO:683-14-0 |
| TERMINAL DUAL LVL COMBI-FT 22-10 AWG P/N::E10537 For Top Drive |
| DT18761 GEARCASE GUIDE, ROTARY MANIFOLD, HR |
| E11417 RTD, 1.5 IN, STRAIGHT, BAYONET, 10 FT |
| AY19681 DIE BLOCK ASSY, INTEG., 5.75 – 9.00 |
| VIEWCOVER RETAINER FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: 911-12-0 |
| PINION FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: DT15090 |
| M25-1001-010 MAGNET, GEARCASE |
| 681-11-1-002 SHIM, 0.002″ |
| LW-1000-NL LOCKWASHER, 1 NORD-LOCK |
| GOOSENECK ASSEMBLY, 4 BORE, 7500 WP FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: AY14632 |
| CYL, HYD, STRK 1, HANDLER LOCK FOR TOP D RIVE PT.NO:920-11-0 |
| FS-0625NC-0400 CAPSCR, FLAT HD SOC, 5/8-11UNC x 4.00 |
| HYDRAULIC CYLINDER FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: H18-1506-001 |
| VALVE, PO CHECK, ALUMINUM FOR TOP DRIVE PT.NO:738-12-0 |
| BEARING CUP FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: M01-1017-010 |
| SPRING, 1.50 OD, 0.75 ID, 10 LG FOR TOP DRIVE PT.NO:M14-1018-010 |
| SH-0750NC-0250-W CAPSCR, HEX SOC HD, 3/4-10UNC x 2.50, W |
| RETAINER, SPLIT RING, 750 TON, 12.38 DIA FOR CANRIG MODEL 1275AC-681 TOP DRIVE DRILLING SYSTEM PART NO: DT10073 |
Telephone
E-MAIL