| Seal Н2537-24A Halco-2500 |
| SPRING PSZ75A-3-03 |
| Blowout valve, build in, bottom 114706-500 |
| HOUSING BOLT MAIN BEARING AH1301010215 |
| 5325-678-7215 SEALANT, SEALING COMPOUND |
| O-RING S01-1279-01N |
| Oil filter for secondary filtration ELY-00 (JC-50 winch) |
| retaining ring135GB/T 893.1BOP PPG 2FZ35-35 |
| V-Belt 8V-4L-48-30 |
| Insider Retainer NB800M.02.04 |
| 603450602 SEAL MECHANICAL OF PUMP 1X1.5 |
| Cone of sand separator 10 “assembly 6066-51 |
| rotating spring 100183-001 |
| axis FY50-01.06A |
| Mechanical seal H22451-1A |
| GAUGE, PRESSURE, 0 – 3000 PSI, SS N01-1003-010 |
| 54322+77 NAMEPLATE, GROUND |
| bolt 1134261 |
| Friction Clutch Plate p/n 29549470 |
| Brake band XJFH-5/35-5500 |
| POWER CONNECTOR 110022-1B |
| 1441471 #8 FLAT HEAD SHEET METAL SCREW/SQUARE DRIVE |
| woodward 9907-014 2301Agovernorlow voltage 10-40VDC FWD |
| 6I-0497 RING-PISTON |
| Pin, Elevator Latch 51402-12 |
| Packing HG4-337-66 |
| Roller Gasket TQ35-05-40 |
| Large Block assembly for drilling drawworks JC50DB PSQ501.08.00 |
| Quick disconnect connection assembly QKD153-02SM, DN7, thread PT1 / 4 “19P (nipple and socket) |
| BOP front coverORingFZ897.1.03B PPG 2FZ35-35 |
| 4202001890 Hexagon Head Bolt Perfect Thread M24*2*90 |
| 840021 X-Over TNC 61 LH Box x 6-5/8 Reg LH Pin |
| Cap, valve GH161-05.13 (G) |
| Plug screw 5″ (d127 MM.) 01.01-26MB model ZQ203-100 |
| S01-1279-01N |
| Valve Section 210 LPM Float Center M854000243-HXXH |
| Roller Jaw model ZQ203-100 Roller 01.01-12M, d=120 MM. |
| tilted plate locked up 6.40.066-02-123 (01.01-29MA) ZQ203-100 |
| Seal 65×90×12, HG4-692-67 |
| Contactor EATON XTCE012B10 |
| Electronic Ballast CEB12236 |
| flow valveSpare part number:5126000551 |
| Bolt; p/n: 50616-20-C; Manufacturer: NOV; Equipment: topdrive TDS-10SH |
| Sprocket Gear 30158574 |
| Pad Wear Casing 6X5X14 2500 SUPREME H2504-01-30A |
| Intermediate tie rod oil seal/Single lip oil seal set107.11.97.00/140 x 109 x 14 |
| PLATE SHEAR CHENGDU WJQ56J0003 |
| RELIEFVALVELOWFLOW(RBAC‐LEN) 111664-1EN |
| P/N:m16-1000-020 |
| Jaw Shaft p/n 0101-12M (3 1/2″ Jaw) |
Telephone
E-MAIL